How To Paint A Car Q&A Part 2 - Paint Biting, Orange Peel, Rust Prevention
220 views · Published 8 December 2014 · 12:05 · Indexed 28 October 2026
Channel: LearnAutoBodyDIY · 2014 · Autos & Vehicles
How To Paint a Car – Go to http://www.learnautobodyandpaint.com/ for more of our BEST trainings! Join VIP Here: http://www.learnautobodyandpaint.com/vip-offer/ Read the Blog: DIY Auto Body Work And Painting Q&A – Paint Biting – Orange Peel – Rust Prevention: http://www.learnautobodyandpaint.com/diy-auto-body-work-and-painting/ This is Part 2 of the LearnAutoBodyAndPaint DIY Auto Body Work And Painting Q&A. If you have any more questions after watching the video, you can post it in the comments below. “Hi Tony, when I paint my fender with base coat, it comes out cracking and one time it came out looking like I dripped lacquer thinner on a spot causing it to look wrinkled. I sanded everything down, re-primed, sanded the primer, then repainted and same thing happens.” Okay, I don’t know what kind of primer you were using but my hunch is, you could have used a lacquer primer. It could have dropped the area down and ate it up. That’s one possibility. But if you were using a 2K primer, the only thing that I can think of is, your panel was dirty – I mean something like, there must have been some oil somewhere, maybe someone nearby was spraying WD-40 (a penetrating oil and water-displacing spray). It’s odd that it’s still the same thing despite doing those remedies that you mentioned. What I really suggest is for you to make sure your surface is really clean. That’s what I really think happened, you might have had a contaminated surface. “I just did my first paint job on a 1990 Chevy pick-up and it was orange-peeled. I’m doing my Mustang next. So how do I figure out the right air setting on the gun to get away from the orange peel?”…Kevin Burchett Orange Peel is caused by a few things – pressure, spray gun, or the material. For pressure, you should be spraying at about 28-29 psi when you’re doing clear coat. And don’t be afraid when you’re laying your clear coat on. You’d want to be about 6-8 inches away from your panel when you’re spraying it on. Another reason could be, a bad spray gun which is not atomizing your materials correctly. If you’re using a cheap spray gun, chances are, you’re not going to get the best results. You might not get the finest atomization possible. Good thing you can get a high-quality spray gun at a fraction of the cost. I’m talking about the Warwick line of spray guns that you can get at the LearnAutoBodyAndPaint Store! For $200-$300 or maybe even cheaper like if you get the 904. They’re excellent, great guns with high atomization. At the least, try to use a good, decent spray gun. Something in the mid to high quality one. Finally, it could also be your material mixture. If you don’t have the proper mixture with your clear coat, that could also cause the problem. If it dries too quickly, it will give you a dry, orange-peely look so make sure you’re mixing your materials correctly. “So you said you live by the ocean and you use vinegar and water or Naval Jelly for rust. I live in the Midwest and we get snow and rain a lot and they come and salt the streets. We get a lot of surface rust. What do I use then? I see a lot of confusion on this. What is the best thing to use? Because you will see some pit sometimes, and other times, pinholes…then again, other times just a little rust with bubbles in the paint.” Well, there’s two different things here…Rust Prevention and Rust Repair. So if you already have rust spots in your car, you have to kill it with an acid. Salt is not an acid. It’s part acid and part base…combined, makes it neutral. So, salt itself is neutral. It turns acidic and damages your car when it mixes with other elements – rainwater, dirt, the weather, etc. If you know boat people, marine people, jet ski owners…notice how after they’re done using their equipment from the ocean, they hose everything down and rinse it out with plain water? So if you want to prevent rust, after you go out in your car in the snow and you get salt all around it – in the fenders and everywhere else…the only real way to do it is, rinse your car down with water when you get home. Just like those boat owners and marine guys do. For rust repair, you need to kill your rust with acid. So if you’re preparing your car for paint and you need to fix some rust spots, you will need to grind down those areas, sand them down and put some vinegar on it to kill the rust. You can even use Coca-Cola (which contains phosphoric acid), citric acid, or salt and lime mixture. Watch the video below and discover how to better use soda instead of drinking it. :D https://www.youtube.com/watch?v=z7OdX42NjWQ Connect on Facebook for More FREE Updates: https://www.facebook.com/learnautobod...https://www.facebook.com/learnautobodyandpaint Connect on Google Plus: https://plus.google.com/+HowToPaintYourCar/posts Shop Here: http://www.learnautobodyandpaint.com/shop/
More from this channel
-
7:43
Live Demo- High Speed Buffers - Car Buffer - Car Polisher Buffer - Car Buffing!
-
5:18
How To Fix a Scratch on a Car - Buffing Out Scratches!
-
3:00
What Michael Thinks About LearnAutoBodyAndPaint.com VIP Club - Member Testimonial
-
5:23
FREE Auto Body Repair Tips! - Auto Body Tools - DA Sanders, In Line Sander - How To Sand a Car
-
5:45
LearnAutoBodyAndPaint.com VIP Member Testimonial Case Study - Diauante from Georgia
-
1:26
LearnAutoBodyAndPaint.com VIP Member Review - Newton from NY.
-
1:26
Rustoleum Paint Job Questions _ Answers on My Blog
-
4:14
What is a Clay Bar - How To Claybar Your Car Fast & Easy