Block Sand Body Filler in Minutes- Learn How To- Do it Yourself from Home

4,716 views · Published 11 January 2016 · 24:36 · Indexed 14 November 2026

Channel: LearnAutoBodyDIY · 2016 · Autos & Vehicles

Watch on YouTube

Get your Free New A-Z Guide To DIY Auto Body And Paint  Success Manual here : http://www.learnautobodyandpaint.com/free-autobody-manual/

Get complete auto body and paint DOMINATION and training here: http://www.learnautobodyandpaint.com/vip-offer/

Read The Blog Here: http://www.learnautobodyandpaint.com/how-to-block-sand-body-filler-in-minutes/

So in this Google Hangout video, I’m going to give you tips and show you how to do block sanding.
I have a car with couple of dents which I filled with bondo and sand it down with 80-grit sandpaper.  We have dents that are corned and some are flat ones. 

Now, let’s talk about blocks.

The holy block has holes on one side and flat surface on the other.  I like to hold it where I can put my fingers in the holes.  It’s easier to use that way because it gives you a little bit of grip while blocking.

I wrap it with an 80-grit sandpaper disc and put some water into the holes so the water dribbles on the surface while I’m wet sanding.

I also have a Dura-Block that you can use on curves.  It’s rubbery and you can roll up your sandpaper around it.  It’s especially good on classic cars where there are curvy areas, especially around the lights.

You can also use these old school rubber blocks.  You can use anything as a block. Let your imagination run wild.
When you sand an area, you have to do crisscross sanding and follow the body line.  The goal is to feather out the edges.

If you want to make sure that all the dents are taken out, use a regular rattle can, black paint to check.  Spray the guide coat and let it dry.  The dark areas are the low spots.

Make sure to constantly hit your sandpaper pad to take all the dust off.

Once you get the general shape done and you don’t feel any dent, get a 240-grit or 280-grit sandpaper and scuff the area then prime it.
You have to make sure to sand the whole area so your primer is going to blend into it.
Once your primer dries, you can go ahead and wet sand it with 400-grit sandpaper.  If your primer didn’t take care of the pin holes and deep scratches in your bondo, fill it with a little bit of glaze putty.

Your primer should take care of little ripples when you block sand it.

You can use from 240-grit to 320-grit sandpaper to scuff and smoothen the bondo.  It doesn’t really matter as long as you get it a little finer before you prime it.
That’s how you would block sand easily by hand.  If you know how to use a DA sander, use it. It’s a lot quicker and comes in really handy.

I would use a DA sander on all of these block spots.  I have an 80-grit sandpaper on my regular DA sander to take these down.

Keep your DA sander flat on the surface and hold it nice and flat to cut the high spots.  Always follow the body line so you won’t screw up.

If you feel comfortable with the DA sander, finish it off then hit it with a 280-grit sandpaper, then prime it and you’re done.

These are the basics.  I hope you liked it.  I’m going to have the rest of the videos available for you within the LearnAutoBodyAndPaint VIP course.

Please Subscribe, Like, Share and Comment below the video.

Go to LearnAutoBodyAndPaint and get your FREE 85-Page Auto Body DIY Manual.  Do your own DIY auto body a success.  Go ahead and tackle your car now.

Talk soon!  Cheers!

-Tony
 
Get A 85-Page Auto Body & Paint Manual + 7-Day Video Boot-Camp Access Here: http://www.learnautobodyandpaint.com/

Connect on Facebook for More FREE Updates: https://www.facebook.com/learnautobodyandpaint
Connect on Google Plus: https://plus.google.com/+HowToPaintYourCar/posts
Shop Here for Best Value High Quality Spray Guns: http://www.learnautobodyandpaint.com/shop/

More from this channel