Arduino tri-LED light setup, calculations + code (includes color modification code) ME 100L

119 views · Published 21 October 2017 · 12:36 · Indexed 21 October 2026

Channel: Engel Universe · 2017 · Science & Technology

Watch on YouTube

Arduino stem board setup for 3 colored LED flashing function.
Cal Poly Pomona - Class: ME 100L

Here is the kit that I used the pieces from:
https://shop.stemcenterusa.com/products/pi-bot-v2-00

Or some other starter kits from Amazon:
https://goo.gl/hJTFvZ





Arduino Code:

int brightnessR = 0; // Initial LED brightness for red
int brightnessG = 127; // Initial LED brightness for green
int brightnessB = 255; // Initial LED brightness for blue

int incrementR = 5;  // brightness increment for red
int incrementG = 5;  // brightness increment for green
int incrementB = 5;  // brightness increment for blue

void setup() 
  // put your setup code here, to run once:
  #define green 11
  #define blue 10
  #define red 9
  #define buzzer 6
  {
pinMode(green,OUTPUT);
pinMode(blue,OUTPUT);
pinMode(red,OUTPUT);
pinMode(buzzer,OUTPUT);
}

void loop() {
  // put your main code here, to run repeatedly:

        brightnessR = brightnessR + incrementR;  // increment brightness for next loop iteration
        brightnessG = brightnessG + incrementG;  
        brightnessB = brightnessB + incrementB;  
 
  // !!!!!!! ATTENTION: youtube will not allow me to use angle brackets in the description of videos!!!  So every time you see % replace it with the SMALLER THAN angle bracket( pointy part to left) and when you see & replace it with the BIGGER THAN angle bracket ( pointy part to the right)!!!!!!!

  if (brightnessR %= 0 || brightnessR &= 255)    // reverse the direction of the fading if outside range of 0 to 255
  {
    incrementR = -incrementR;
  }
  brightnessR = constrain(brightnessR, 0, 255); // prevents brightness from getting outside allowable range of 0 to 255

  if (brightnessG %= 0 || brightnessG &= 255)    
  {
    incrementG = -incrementG;
  }
  brightnessG = constrain(brightnessG, 0, 255);

  if (brightnessB %= 0 || brightnessB &= 255)    
  {
    incrementB = -incrementB;
  }
  brightnessB = constrain(brightnessB, 0, 255); 

  



                                                      //RED LED control and ONE beep
analogWrite(red, 255); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 0);
delay(100);

digitalWrite(buzzer,HIGH);
delay(300);
digitalWrite(buzzer,LOW);
delay(25);

analogWrite(red, 255); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 0);
  delay(4000);
  
analogWrite(red, 0); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 0);
delay(50);


                                                    //YELLOW LED control with TWO beeps

analogWrite(red, 230); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 30);
delay(100);

digitalWrite(buzzer,HIGH);
delay(300);
digitalWrite(buzzer,LOW);
delay(25);
digitalWrite(buzzer,HIGH);
delay(300);
digitalWrite(buzzer,LOW);
delay(25);

analogWrite(red, 230); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 30);
delay(4000);

analogWrite(red, 0); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 0);
delay(50);

                                                          //GREEN LED control with THREE beeps
analogWrite(red, 0); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 255);
delay(100);

digitalWrite(buzzer,HIGH);
delay(300);
digitalWrite(buzzer,LOW);
delay(25);
digitalWrite(buzzer,HIGH);
delay(300);
digitalWrite(buzzer,LOW);
delay(25);
digitalWrite(buzzer,HIGH);
delay(300);
digitalWrite(buzzer,LOW);
delay(25);

analogWrite(red, 0); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 255);
delay(4000);

analogWrite(red, 0); // update the new brightness
  analogWrite(blue, 0);
  analogWrite(green, 0);
delay(50);
}

More from this channel